Note that this sequence must be done in 5 seconds or the device turns back of. This sequence must also be done in 5 seconds or the device remains on. Directional Pad - Press arrows to highlight a selection on the screen or hold arrows down to access keyboard shortcuts when sending messages. To avoid triggering a false alarm, make sure your SOS slider is locked. Press the Left Arrow and then Enter. The screen displays a welcome message and begins the setup process.
Your inReach Explorer requires a satellite airtime plan and an online Explore account to send and receive messages, much like a mobile phone plan Note: Your inReach Explorer GPS features will not work without a satellite airtime plan.
The inReach uses Iridium's satellite network to track, share information, and send and receive messages. To choose your plan and set up your account, use the DeLorme Explore website:. Go online from your computer to explore. During the online account setup process, choose your inReach service plan, enter your payment information and contact details, and add your emergency contacts that will be used if your inReach Explorer is placed into SOS mode.
Link your Twitter and Facebook accounts to share messages with your friends by selecting the Social tab. Set up your MapShare web page to let others follow your trip and send you messages on your inReach Explorer by adjusting the MapShare options on the Social tab. Create some commonly used text messages that are stored in your device, e. The inReach Explorer needs a clear satellite signal from the sky to complete the setup process. Go outside and stand in an open area away from tall buildings, roof overhangs, and trees.
When you set up your Explore account, DeLorme sent you a welcome message for testing your inReach. Your device receives this message during the activation process. When you have a clear view of the sky, press Enter to activate and receive your message. The activation process could take up to 20 minutes. Activation of your inReach with the Iridium satellite network is a one-time step that uses a diferent process than standard inReach functions. To read your welcome message, select Messages from the device's home page and choose the new message from DeLorme.
Send a test reply to DeLorme. Select Type Reply, and then type a message using the on-screen keyboard. Press Send. DeLorme sends you an automatic reply when your message is received. Your inReach Explorer listens for waiting messages every 20 minutes by default. After activating your inReach Explorer, set up the device with the information you will need while on your trip.
You can return to the Explore website at any time to change or update this information. The device automatically checks compass calibration and tells you to calibrate when necessary. For best performance, calibrate your digital compass any time the device prompts you, or manually calibrate before a trip when you expect compass use to be important. Rotate the inReach, turning all six sides of the device to the ground.
Continue until the inReach beeps to report successful calibration. The inReach Explorer uses a barometric altimeter to give accurate elevation readings when you are climbing or descending.
The device automatically calibrates the barometric altimeter using GPS elevation each time it is powered on. Auto calibrating with GPS elevation is best if you do not know the correct elevation or pressure for your location.
Launching the System Management Console. Adding a server. Adding and configuring the Accounting Module. Adding and configuring the IP Client Manager. Configuring the Provisioning Module.
Adding and configuring the Web Client Manager. Installing and configuring the Oracle Monitor. Installing the iPlanet Monitor. Verification procedures.
Verifying Server2 application server. Verifying the database load imssipdb deployment. Deploying the PC Client. Reloading IP addresses after system installation. The content of this documentation was current at the time the product was released. To check for updates to the latest documentation and software for MCS , click one of the following links:.
The best way to get technical support for Nortel products is from the Nortel Technical Support web site:. This site provides quick access to software, documentation, bulletins, and tools to address issues with Nortel products. From this site, you can:. If you do not find the information you require on the Nortel Technical Support web site, and you have a Nortel support contract, you can also get help over the phone from a Nortel Solutions Center.
Outside North America, go to the following web site to obtain the phone number for your region:. To locate the ERC for your product or service, go to:. If you purchased a service contract for your Nortel product from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller. This system allows more effective cost management for smaller-sized enterprises. This document describes the installation of the 2-server Sun Fire V Solaris system.
The IP configuration consists of one public IP address. The following figures show the possible network configurations. The rest of this document will refer to the example data in the figure that follows.
Print and refer to this example while executing this installation. Print and complete the CSI datasheet with your own configuration to assist in executing this installation. Configure the pc you are using for management services with an IP address that is in the same subnet of the IP address range used for the Sun Fire V The 2-server V Solaris system is non-redundant. Since redundancy is not built into the system, a server failure will result in the loss of services.
The 2-server V Solaris system has a mirrored disk. In the event of a disk failure, the failed disk should be replaced as soon as possible. The 2-server V Solaris system has the following limitations:. Doing any maintenance while the system is live may have adverse effects on call processing. NN, that accompanies the MCS product and to your customer-specific information CSI datasheet for your system requirements.
For more information on component installation and commissioning tasks, refer to the specific component documentation:. Make sure you install the latest software loads. Check with your support team for the correct latest load.
Fill out the datasheet with relevant information from your system administrator. You must have read and understood all the Release Notes before the installation begins. Nortel Networks strongly recommends the use of high-speed data network connectivity for optimum remote service capability. Without broadband connectivity, remote service options are limited. Nortel Networks also recommends following standard data center conventions for having a Universal Power Supply UPS as the power backup for the servers.
Refer to Minimum and recommended requirements for customer-provided PC on page See Table 2, Mapping of Kit. Networks recommends that you install the same CDs on both servers at the same time to reduce installation time.
Disk 6 only needs to go on. Server 1 the server on which the Management and Accounting Modules reside. There are six Oracle disks, with one copy, going on Server 1 the server on which the Database Module resides.
Configure your management pc to have an IP address that is in the same subnet of the IP address range used for your servers. Minimum and recommended requirements for the customer-provided management PC include assuming you are not running anything else on the pc :. This requirement is in addition to the memory requirements of the operating system and other concurrent applications.
In this case, the free 50MB on drive C will not be used, but is required for the installation to complete successfully. If a power outage occurs, bring the server for the Database Module into service before bringing the other servers into service. If other servers do not come up, restart the server for the Management Module. Note: Each V server uses two 2 ethernet cables to connect the V servers to the layer-2 switch. Refer to the following diagram that displays the mounting for the rack.
Refer to the Media Application Server documentation for more information. Refer to customer-specific gateway installation documentation. Note 1: Net 0 and Net 1 are for redundancy. It is preferable that each Ethernet port get cabled to a different layer-2 switch, if available, for maximum redundancy. Note 2: The two Ethernet switches are physically linked together through either cascade modules or Ethernet links.
Note: This server is only available in an AC power configuration. If the network is down, or the server needs to be configured or restarted, use the console port A. Note : This cable is only connected to configure the terminal server. Note: After the terminal server has been configured, the connection between the management PC and the terminal server is not needed, and the cable can be removed. Ten47 Cable Box CableGuard. Eaton Control Unit Crouse-hinds series.
Eaton Recording Equipment Crouse-hinds series. Eaton Enclosure Crouse-hinds series. Extron electronics Cable Box Cable Cubby Eaton Switch Crouse-hinds series. Explosion protected control units made of plastic or stainless steel GHG
0コメント